Machining Factory Services
Mill-turn combines turning and milling in one machine, so a round part that also needs milled features — flats, slots, cross-holes, keyways — is finished in a single setup instead of being passed between a lathe and a mill. That single setup is the point: it removes the re-fixturing that introduces error and time.
This factory runs multi-task centers in the Mazak and Brother class, including twin-spindle and five-axis mill-turn machines, so complex round parts stay in one setup from start to finish. For an auditor, mill-turn is easy to verify because the machines are visually distinct — a mill-turn center has both a turning spindle and a milling spindle, and there is no confusing it with a plain lathe.
What does the precision grinding service cover?
Grinding is what takes a surface past what a cutting tool can hold — bearing seats, roundness-critical journals, and surfaces that need a ±0.002 mm finish or a specific roughness. It is the process that separates a "precision" claim from a precision result, because grinding is how the tightest tolerances and best finishes are actually achieved.
This factory runs 7+ grinders covering surface, centerless and cylindrical grinding, holding ±0.002 mm. The three types map to three needs: surface grinding for flat faces, cylindrical grinding for outside diameters, and centerless grinding for high-volume round parts that need consistency without a center hole. As with every other service, the machines are on the floor to be counted.
Grinding is also where the surface-finish call-out is decided. A turned or milled surface lands around Ra 1.6 to 3.2 µm; grinding takes the same face to Ra 0.8 µm or below, which is what a sealing face or a bearing seat needs. When a print calls Ra 0.8 µm and the shop has no grinder in the list, the finish will be chased with a cutting tool, and it will not be the surface the drawing asked for. Matching the Ra call-out to a real grinding process is the same kind of evidence check as matching a tolerance to a CMM.
What materials do these services cut?


The process is only half the question; the material is the other half, and it changes how a part machines. Aluminum cuts fast and clean, stainless wears tools, titanium and hardened steel need slower feeds and careful toolpaths. A service menu that does not name materials is dodging the part of the job that actually determines cycle time and tooling.
| Material family | Grades run | Audit note |
|---|---|---|
| Aluminum | 6061, 6063, 6082, 7075, 2014 | Most common prototype and production choice |
| Stainless steel | 303, 304, 316, 316L, 17-4PH | 303 free-machining, 316L corrosion, 17-4PH strength |
| Carbon / alloy steel | 1018, 1045, 4140, 4340, 12L14 | Carburizing or nitriding for wear parts |
| Brass / copper | C360, H62, C110 | Electrical and thermal conductivity |
| Titanium / magnesium | TA2, TC4 (Grade 2 / 5) | Titanium stress relief above 500 °C is outsourced |
| Engineering plastics | ABS, POM, nylon, PTFE, PEEK | Non-metal prototypes and insulators |
How do you audit the services down to the machine?

The service menu becomes auditable the moment the machine list stops being a category and starts being a count. Ask the shop to name the families and how many of each run on the floor, then match that list to what you see. A manufacturer can point at each machine and say what it cuts; a broker cannot.
This factory states the list plainly: 3-axis milling (50+), 4-axis (20+), 5-axis (20+), CNC turning (25+), mill-turn in the Mazak and Brother class, and grinding (7+, surface / centerless / cylindrical). Each family maps to a geometry, so the list doubles as a DFM answer — send a drawing and the factory can name, in the same breath, which process your part needs and which machines will run it.
Why does keeping the process in-house matter to a buyer?
Because every hand-off between facilities is a place where lead time, tolerances and accountability leak. A part that moves from a mill to an outside grinder to an outside anodizer passes through three schedules and three quality records, and when something goes wrong the finger-pointing starts. In-house processes mean one accountable supplier for the metal-cutting chain.
That is why this factory keeps milling, turning, mill-turn and grinding under one roof. The secondary finishing — anodizing, plating, heat treatment — is bundled through qualified partners and named as such, because honesty about who does what is itself part of the audit. What stays in-house is the core cutting, and that is where the tolerance lives.
How does a drawing become a finished part across these services?
The service menu is not four isolated processes; it is a chain a drawing travels along. A part arrives as a STEP or 2D print, the geometry is read to name the first process, the tolerance and Ra call-outs decide whether a second process — usually grinding — joins the chain, and the finishing steps are added last. Each hand-off is a place where the audit looks for an owner, a schedule and a record, because each hand-off is where time and accountability leak if no one owns the whole chain.
The value of keeping the core cutting under one roof is that the chain has fewer seams. Milling, turning, mill-turn and grinding run in the same building, so a part that moves from mill to grinder moves across a floor, not across town. When you audit the services, you are really auditing the chain, which processes the shop owns, which it partners, and whether each seam in between is named and recorded rather than hidden.
What this shop actually runs
We machine every part in our own 6,800 m² plant in Dongguan, China, on 100+ CNC machines with 100+ staff. The machine list by category:
- 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Cut on compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
- 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Cut on prismatic parts, plates, brackets, housings.
- Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Cut on long, slender rotational parts at ±0.002 mm.
- CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Cut on shafts, bushings, flanges up to ±0.002 mm.
- Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Cut on hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
- Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
- Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.
Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk >= 1.67 initial on key characteristics, Cpk >= 1.33 ongoing.
Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.
Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.
Contact: Felipe Iglesias, [email protected], +86 13126536955.
Match your part to the right machining service
Send your drawing to [email protected] or call +86 13126536955 — process, machine and tolerance named in one pass.
Frequently Asked Questions
What machining services does this factory run?
In short, Four core processes, all in-house: CNC milling (3-, 4- and 5-axis), CNC turning, mill-turn and precision grinding, plus bundled secondary operations. Each service maps to a machine family, a tolerance and a workpiece envelope, so an auditor can verify what is actually on the floor rather than what is on a brochure.
Which service is right for my part geometry?
In short, The service follows the geometry. Round parts such as shafts and bushings go to turning, prismatic parts such as housings and brackets go to milling, round parts with milled features go to mill-turn for a single setup, and bearing seats or roundness-critical surfaces go to grinding.
What tolerances does each machining service hold?
In short, CNC milling and turning hold ±0.003 mm (milling) / ±0.002 mm (turning), and precision grinding holds ±0.002 mm. These are verified on Hexagon CMMs with process capability Ppk ≥ 1.67 at the initial study on key characteristics and Cpk ≥ 1.33 on general characteristics, so the tolerance is backed by measurement rather than a brochure claim.
How large a part can the factory machine?
In short, Milling handles workpieces up to 1300 × 700 × 600 mm and turning up to Ø720 × 1280 mm. Stating the envelope up front means you can tell from a drawing whether the part fits the capacity before a quote, instead of discovering it after an order is placed.
Are the services auditable down to the machine?
In short, Yes. The machine list is stated by family and count — 3-axis (50+), 4-axis (20+), 5-axis (20+), 25+ lathes, mill-turn centers in the Mazak and Brother class, and 7+ grinders — so a buyer or auditor can match the claimed capacity to the machines on the floor during a walkthrough.
Can secondary operations be bundled with machining?
In short, Yes — anodizing, plating, powder coating, painting, brushing, polishing, deburring and heat treatment can be bundled so you receive finished parts rather than machined blanks. Finishing runs through qualified partners and is stated as such, so ownership of every step is transparent to an auditor.
What is the MOQ and lead time for these services?
In short, The MOQ is 1 piece across all services, so you can validate a first article before committing to volume. Lead time is roughly 3, 7 or 30 days depending on part complexity and the number of process steps, with surface finishing pushing a part into the longer 30-day tier.
How do I get a quote for a machining service?
In short, Send your STEP, IGES or 2D drawing to [email protected]. You receive a design-for-manufacturing review that names the right service for your geometry, plus a quote, usually within one business day, with any cost or tolerance issues flagged before you commit.
Continue reading: Machining Factory · Machining Factory · Machining Factory Quality Control
Standards referenced on this page
- ASTM B211/B211M-19 — Standard Specification for Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
- ASTM A582/A582M-12 — Standard Specification for Free-Machining Stainless Steel Bars
- ISO 9001 — Quality management systems — Requirements
